[2661] in linux-scsi channel archive
Errors/problems/questions
daemon@ATHENA.MIT.EDU (Dave Wreski)
Sun Oct 19 20:58:49 1997
Date: Sun, 19 Oct 1997 20:56:03 -0400 (EDT)
From: Dave Wreski <dave@nic.com>
To: linux-scsi@vger.rutgers.edu
Hey guys. I was copying about 600M in several xterms at once, to prepare of
cutting a CDR. All of the sudden everything just stopped, and then 10
seconds later started. I wondered if you could tell me if any of these
indicate a problem with the drive, bug in the aic7xxx software, or
otherwise. This is 2.0.31, and I've included some information about the
disks and controller at the end. The following snippets are from my
messages:
Oct 19 01:52:34 gossamer kernel: scsi : aborting command due to timeout :
pid 122096, scsi0, channel 0, id 2, lun 0 0x08 00 0a 0c 0c 00
Oct 19 01:52:56 gossamer kernel: SCSI host 0 abort (pid 122096) timed out -
resetting
Oct 19 01:52:56 gossamer kernel: SCSI bus is being reset for host 0 channel
0.
Oct 19 01:52:56 gossamer kernel: (scsi0:2:0) Abort_reset, scb flags 0x1,
while idle, LASTPHASE = 0x1, SCSISIGI 0x0, SEQADDR 0x4, SSTAT0 0x5, SSTAT1
0xa
Oct 19 01:52:56 gossamer kernel: (scsi0:2:0) Queueing an Abort SCB.
Oct 19 01:52:56 gossamer kernel: SCSI bus is being reset for host 0 channel
0.
Oct 19 01:52:56 gossamer kernel: (scsi0:2:0) SCB 13 abort Tag completed.
Oct 19 01:52:56 gossamer kernel: (scsi0:2:0) Reset device, active_scb 9
Oct 19 01:52:56 gossamer kernel: scsi0: (targ 2/chan A) matching scb to
(targ 2/chan A)
Oct 19 01:52:56 gossamer last message repeated 14 times
Oct 19 01:52:56 gossamer kernel: (scsi0:2:0) Aborting scb 13
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: MICROP Model: 4110-09NB_Nov18b Rev: TN0F
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: SEAGATE Model: ST32151W Rev: 0322
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 02 Lun: 00
Vendor: SEAGATE Model: ST51080N Rev: 0913
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 06 Lun: 00
Vendor: TOSHIBA Model: CD-ROM XM-5701TA Rev: 0167
Type: CD-ROM ANSI SCSI revision: 02
Adaptec AIC7xxx driver version: 4.1/3.2
Compile Options:
AIC7XXX_RESET_DELAY : 15
AIC7XXX_TAGGED_QUEUEING: Enabled
AIC7XXX_PAGE_ENABLE : Enabled
AIC7XXX_PROC_STATS : Disabled
Adapter Configuration:
SCSI Adapter: Adaptec AHA-294X Ultra SCSI host adapter
(AIC-788x chipset)
Host Bus: Wide
Base IO: 0x9000
Base IO Memory: 0xe0804000
IRQ: 9
SCBs: Used 17, HW 16, Page 255
Interrupts: 298318
Serial EEPROM: True
Extended Translation: Disabled
SCSI Bus Reset: Enabled
Ultra SCSI: Enabled
Target Disconnect: Enabled
Thanks,
Dave
