[729] in linux-scsi channel archive
Problem with scsi 3.0.0 bootkernel disk
daemon@ATHENA.MIT.EDU (Angela Bayley)
Fri Oct 27 15:56:07 1995
Date: Fri, 27 Oct 1995 11:13:27 +0000 (GMT)
From: Angela Bayley <amb@jb.man.ac.uk>
To: linux-scsi@vger.rutgers.edu
I am trying to upgrade to Linux 3.0.0 but I am having problems trying to
boot the scsi bootkernel 3.0.0 disk. The Fujitsu M1606S-512 disk at id 0
is detected correctly, but the driver reports continuous timeouts trying
to access the Fujitsu M2694ES-512 disk at id 1. The log goes as follows:
Console: colour EGA+ 80x25, 1 virtual console (max 63)
Calibrating delay loop.. ok - 33.55 BogoMips
Serial driver version 4.11 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
hda: IBM-DALA-3540, 516MB w/96KB Cache, LBA, CHS=1049/16/63, MaxMult=16
ide0: primary interface on irq 14
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
aha152x: porttest: failed
BusLogic SCSI: buslogic_out: failed(4): BusLogic SCSI: buslogic_stat: status=39
intrflags=84
BusLogic SCSI: setup_mailboxes: failed setting up mailboxes.
Configuring Adaptec (SCSI ID 7) at IO:330, IRQ 11, DMA priority 5
eata_dma: no BIOS32 extensions present. This release still depends on it.
Skipping scan for PCI HBAs
eata_pio: no BIOS32 extensions present. This release still depends on it.
Skipping scan for PCI HBAs
EATA0 address 0x1f0 in use: skipping probe
EATA0 address 0x330 in use: skipping probe
scsi0 : Adaptec 1542
scsi : 1 host.
Vendor: FUJITSU Model: M1606S-512 Rev: 6217
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, id 0, lun 0
scsi: aborting command due to timeout: pid 3, scsi 0 id 1 lun 0 0x12 00 00 00
ff 00
scsi: aborting command due to timeout: pid 3, scsi 0 id 1 lun 0 0x12 00 00 00
ff 00
SCSI host 0 abort() timed out - resetting
aha1542_out failed(2): Sent BUS DEVICE RESET to target 1
Sending DID_RESET for target 1
aha1542_out failed(2): Sending DID_RESET for target 1
aha1542_out failed(2): Sending DID_RESET for target 1
aha1542_out failed(2): Sending DID_RESET for target 1
aha1542_out failed(2): Sending DID_RESET for target 1
aha1542_out failed(2): Sending DID_RESET for target 1
aha1542_out failed(2): Sending DID_RESET for target 1
aha1542_out failed(2): Sending DID_RESET for target 1
aha1542_out failed(2): scsi: aborting command due to timeout: pid 3, scsi 0
id 1 lun 0
0x12 00 00 00 ff 00
SCSI host 0 abort() timed out - resetting
aha1542_out failed(2): Sent BUS DEVICE RESET to target 1
Sending DID_RESET for target 1
The last 11 messages are continually repeated and the only way out is to
reboot using Ctrl-Alt-Del. The behaviour is the same if I try "ramdisk
aha1542=0x330,11,5,5" on the LILO command line.
I am currently running Linux 1.1.59 without any problems on the following
configuration:
IBM PS Valuepoint, 486DX2/66, 16MB
IBM-DALA-3540 516MB (DOS C:)
SCSI controller AHA-1542CF BIOS v2.10
Fujitsu M1606S-512 1Gbyte scsi id 0 /dev/sda
Fujitsu M2694ES-512 1Gbyte scsi id 1 /dev/sdb
Creative Labs LaserMate CD-ROM
A sample bootkernel log from the sbpcd 1.2.1 bootkernel disk which I used
to install Linux 1.1.59 is as follows:
Console: colour EGA+ 80x25, 1 virtual console (max 63)
Calibrating delay loop.. ok - 33.55 BogoMips
Serial driver version 4.11 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
hda: IBM-DALA-3540, 516MB w/96KB Cache, LBA, CHS=1049/16/63, MaxMult=16
ide0: primary interface on irq 14
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
SBPCD version 3.4 Eberhard Moenkeberg <emoenke@gwdg.de>
SBPCD: Looking for Matsushita, Panasonic, CreativeLabs, IBM, Longshine CD-ROM drives
SBPCD:
SBPCD: = = = = = = = = = = W A R N I N G = = = = = = = = = =
SBPCD: Auto-Probing can cause a hang (f.e. touching an ethernet card).
...sbpcd messages omitted...
SBPCD: You should configure sbpcd.h for your hardware.
SBPCD: 1 LaserMate CD-ROM drive(s) at 0x0300.
SBPCD: init done.
BusLogic SCSI: buslogic_out: failed(4): BusLogic SCSI: buslogic_stat: status=39
intrflags=84
BusLogic SCSI: setup_mailboxes: failed setting up mailboxes.
Configuring Adaptec at IO:330, IRQ 11, DMA priority 5
EATA (Extended Attachment) driver version: 2.31a
developed in co-operation with DPT
(c) 1993-95 Michael Neuffer neuffer@goofy.zdv.uni-mainz.de
No BIOS32 extensions present. This release still depends on it. Sorry.
Registered HBAs:
HBA no. Boardtype: Revis: EATA: Bus: BaseIO: IRQ: DMA: Ch: ID: Pr: QS: SG: CPL:
scsi0 : Adaptec 1542
scsi : 1 host.
Vendor: FUJITSU Model: M1606S-512 Rev: 6217
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, id 0, lun 0
Vendor: FUJITSU Model: M2694ES-512 Rev: 8134
Type: Direct-Access ANSI SCSI revision: 01 CCS
Detected scsi disk sdb at scsi0, id 1, lun 0
scsi : detected 2 SCSI disks total.
SCSI Hardware sector size is 512 bytes on device sda
SCSI Hardware sector size is 512 bytes on device sdb
Memory: 14888k/16384k available (872k kernel code, 384k reserved, 240k data)
This processor honours the WP bit even when in supervisor mode. Good.
Swansea University Computer Society NET3.019
Swansea University Computer Society TCP/IP for NET3.019
IP Protocols: ICMP, UDP, TCP
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 1.2.1 (root@fuzzy) (gcc version 2.5.8) #3 Sun Mar 19 10:17:12 CST
1995
Partition check:
sda: sda1 sda2
sdb: sdb1
hda: hda1
VFS: Mounted root (ext2 filesystem).
Adding Swap: 41980k swap-space
SBPCD: sbpcd_open: no disk in drive
Does anyone know what has changed to cause this problem, or seen anything
similar?
Angela Bayley
