[5194] in linux-scsi channel archive
AHA-1520x Timeouts
daemon@ATHENA.MIT.EDU (Buford the Playa)
Sun Nov 22 07:37:13 1998
Date: Sun, 22 Nov 1998 02:34:43 -0600 (EST)
From: Buford the Playa <livng1@iamerica.net>
To: linux-scsi@vger.rutgers.edu
In-Reply-To: <Pine.LNX.3.95.981121215504.380A-101000@localhost>
Greetings. I'm having trouble with mounting a zip disk in RedHat 5.1 Using
an Adaptech AHA-1520b which I understand is a troublesome card anyway.
I finally got the card working in linux and these are the messages I
receive on boot up :
aha152x: processing commandline: ok
aha152x: BIOS test: passed, detected 1 controller(s)
aha152x0: vital data: PORTBASE=0x340, IRQ=10, SCSI ID=7,
reconnect=enabled, parity=enabled, synchronous=disabled, delay=100,
extended translation=disabled
aha152x: trying software interrupt, ok.
scsi0 : Adaptec 152x SCSI driver; $Revision: 1.18 $
scsi : 1 host.
Vendor: IOMEGA Model: ZIP 100 Rev: J.02
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi removable disk sda at scsi0, channel 0, id 5, lun 0
Vendor: SONY Model: CD-R CDU926S Rev: 1.1f
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
scsi : detected 1 SCSI cdrom 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1 GB]
sda: Write Protect is off
Partition check:
sda: sda1
hda: hda1 hda2 < hda5 hda6 >
hdb: hdb1
aha152x: ignoring spurious interrupt, nothing to do
QUEUE STATUS:
issue_SC:
current_SC:
none
disconnected_SC:
waiting: SCSISEQ (); SCSISIG (DATA OUT); INTSTAT (lo); SSTAT (BUSFREE
PHASECHG ); SSTAT (); SXFRCTL0 (CH1 ); SIGNAL (); SELID (a0), SSTAT2
(SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 (); DMACNTRL0 (16BIT
PIO READ ); DMASTAT (DFIFOEMP )
enabled interrupts ()
When I attempt to mount a zip drive using the command "mount /dev/sda1
/mnt/zip" I receive the following errors :
scsi : aborting command due to timeout : pid 13, scsi0, channel 0, id 5,
lun 0 Start/Stop Unit 00 00 00 01 00
aha152x: abort(), SCpnt=0x00090410, QUEUE STATUS:
issue_SC:
0x00090410: target=5; lun=0; cmnd=(Start/Stop Unit 00 00 00 01 00
); residual=0; buffers=0; phase |not issued|; next=0x00000000
current_SC:
none
disconnected_SC:
waiting: SCSISEQ (); SCSISIG (DATA OUT); INTSTAT (hi); SSTAT (BUSFREE
PHASECHG ); SSTAT (BUSFREE ); SXFRCTL0 (CH1 ); SIGNAL (); SELID (a0),
SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 (); DMACNTRL0
(16BIT PIO READ INTEN ); DMASTAT (DFIFOEMP )
enabled interrupts (ENBUSFREE )
I've searched IRC, the web, the SCSI-HOWTO and usenet. I'm still stuck on
this problem. I would love to get my zip and cd-r working in linux and any
help would be appreciated.
Also, as far as I know this setup is terminated properly and works fine in
windows.
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.rutgers.edu
