[4318] in linux-scsi channel archive
aic7xxx-5.1.0-pre1-2.1.108.patch.gz and 230 Meg MO
daemon@ATHENA.MIT.EDU (Sid Boyce)
Thu Jul 9 02:42:12 1998
Date: Wed, 08 Jul 1998 23:35:54 +0000
From: Sid Boyce <szb50@amdahl.com>
To: linux-scsi@vger.rutgers.edu
This is a multi-part message in MIME format.
--------------280C40B18B1FF14E91A23163
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit
This patch at least detects it, whereas 2.1.108 with the 5.0.19 patch for
2.1.105 didn't under 2.1.108, but works fine for 2.1.107.
The 1.1 Gig HD was always OK, perhaps I have to give some command line
parameters to lilo to get it to look for 2048 byte sectors the MO has.
Keep up the good work Doug.
Regards
--
... Sid Boyce...Amdahl(Europe)...44-121 422 0375
-----------------------------------
Any opinions expressed above are mine and do not necessarily represent
the opinions or policies of Amdahl Corporation.
--------------280C40B18B1FF14E91A23163
Content-Type: text/plain; charset=us-ascii; name="scsi_err"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline; filename="scsi_err"
aic7xxx: Warning - detected auto-termination on controller:
aic7xxx: <Adaptec AHA-294X Ultra SCSI host adapter> at PCI 15/0
aic7xxx: Please verify driver detected settings are correct.
aic7xxx: If not, then please properly set the device termination
aic7xxx: in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
aic7xxx: during machine bootup.
aic7xxx: Cables present (Int-50 YES, Ext-50 NO)
(scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 15/0
(scsi0) Narrow Channel, SCSI ID=7, 16/255 SCBs
(scsi0) Downloading sequencer code... 411 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.0/3.2.4
<Adaptec AHA-294X Ultra SCSI host adapter>
scsi : 1 host.
Vendor: Quantum Model: XP31070W Rev: L912
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:0:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: FUJITSU Model: M2512A Rev: 1509
Type: Optical Device ANSI SCSI revision: 02
Detected scsi removable disk sdb at scsi0, channel 0, id 2, lun 0
(scsi0:0:2:0) Synchronous at 5.0 Mbyte/sec, offset 8.
scsi : detected 2 SCSI disks total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 2203480 [1075 MB] [1.1 GB]
sdb : READ CAPACITY failed.
sdb : status = 1, message = 00, host = 0, driver = 28
sdb : extended sense code = 4
sdb : block size assumed to be 512 bytes, disk size 1GB.
AX.25 Multikiss device enabled
eth0: 3c509 at 0x300 tag 1, 10baseT port, address 00 a0 24 7b 94 a8, IRQ 12.
3c509.c:1.12 6/4/97 becker@cesdis.gsfc.nasa.gov
Partition check:
sda: sda1
sdb:SCSI disk error : host 0 channel 0 id 2 lun 0 return code = 28000002
extra data not valid Current error sd08:10: sense key Hardware Error
Additional sense indicates Internal target failure
scsidisk I/O error: dev 08:10, sector 0
unable to read partition table
--------------280C40B18B1FF14E91A23163--
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.rutgers.edu
